Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Frisco, TX
Frisco homeowners call us most often about gate access control: keypads that stopped recognizing codes, intercoms that ring into dead air, and card readers that quit after a storm. The housing stock here makes the work predictable in some ways (nearly every subdivision uses ornamental steel gates) and tricky in others (Blackland Prairie clay moves posts out of plumb every wet-dry cycle). If your gate won’t respond to a code, remote, or phone app, call Vance Gate Repair at (469) 613-2832. A live person answers.
Why Frisco Homes Are Different
Frisco sits on Blackland Prairie expansive clay. It swells after spring rain and shrinks hard during summer drought, and that cycle racks gate posts, twists hinges, and pulls operators out of alignment. We see the same failure in Phillips Creek Ranch that we see in Newman Village: a gate that worked fine in March binds by August because the post moved a half-inch. On top of the soil, Frisco is one of the most HOA-dense cities in the country. Communities like Starwood and Newman Village keep architectural spec sheets that dictate picket profile, powder-coat finish, and sometimes the approved automation brand. Before any replacement part gets ordered, someone has to confirm the HOA will approve it. That step simply doesn’t exist in older, HOA-light cities. Summer heat above 105°F also cooks control boards in direct-sun operators and brittle-izes nylon rollers faster than homeowners expect.
Our Main Frisco Services
These are the three services Frisco homeowners call about most, each with its own detailed page for this city.
Gate Repair in Frisco
When a gate sags, drags, or won’t latch, the cause in Frisco is usually post movement from clay soil cycling. We pull photos, measure the gap, and write a flat price before any tool touches the gate. In HOA-governed communities, we confirm material specs before ordering. One visit, one written price, one documented fix. See the full scope on Gate Repair in Frisco.
Gate Installation in Frisco
A new gate in Frisco is an HOA approval exercise as much as a construction job. We pull the community’s spec sheet, match picket spacing and powder-coat color, and factor clay-soil post depth into the footing plan. You get a written scope and price before the first post hole is dug. Details on Gate Installation in Frisco.
Gate Motor & Opener in Frisco
Operators on Frisco gates work harder than the same motor in stable soil: every post shift changes the travel geometry and strains the arm. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we recalibrate limits and photo-eyes after any post work. The full breakdown is on Gate Motor & Opener in Frisco.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Frisco
Gate access control in Frisco means the keypad, intercom, card reader, or phone-entry system that decides who gets through. Most systems in this city were installed when the house was built, anywhere from the late 1990s to last year, which means we see three generations of wiring and software in the same subdivision. From the Gate Access Control side, our job is to identify what’s actually failing before replacing anything, then hand you a written price. In Frisco specifically, summer heat kills outdoor keypad membranes and direct-sun control boards faster than the manufacturer’s expected lifecycle, and post movement from clay soil can pull intercom and reader wiring loose at the gate junction.
Keypad Entry
Signs you need it
The keypad beeps but won’t trigger the operator, certain codes stopped working, or the membrane is cracked and sun-baked.
What it costs in Frisco
Replacing a standard gate keypad in Frisco typically runs $180 to $340 installed, depending on the brand and whether new wire needs pulling.
How we do it
We test voltage at the pad, confirm the operator’s radio or wired input, replace the unit, and reprogram all codes with a written record of every change.
Video Intercom
Signs you need it
The indoor monitor rings but shows no video, call audio drops after a few seconds, or the outdoor camera lens is fogged with North Texas sun damage.
What it costs in Frisco
A full video intercom replacement in Frisco runs $450 to $750 installed, with the spread driven by whether the existing wiring is reusable.
How we do it
We verify the power supply, test the camera signal at the monitor, replace the failed component, and photograph the final wiring so any future technician has a map.
What Gate Access Control Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Gate keypad replacement | $180-$340 |
| Gate remote control (one transmitter) | $60-$120 |
| Video intercom replacement | $450-$750 |
Can you fix a keypad the same day in Frisco?
Usually yes. We keep common keypad brands and operator remotes on the truck, and a live person answers the phone around the clock. Call (469) 613-2832 and we’ll tell you what’s available today.
Do I need HOA approval to change my gate keypad in Frisco?
Sometimes, if the keypad housing is visibly different in color or profile. In communities like Starwood and Newman Village, we confirm the spec before ordering. Call (469) 613-2832 and we’ll check for you.
Gate Parts & Welding in Frisco
Gate parts and welding in Frisco is mostly about steel components that failed from soil movement and age: hinges that cracked, posts that drifted out of plumb, rails that bowed, and rollers that disintegrated in summer heat. In communities like Phillips Creek Ranch, the HOA architectural committee can fine a homeowner if a replacement picket doesn’t match the community’s exact profile or powder-coat shade, so part of the work is materials-matching before anything gets welded. From the Gate Parts & Welding end, we document the failed part, quote the replacement and the weld work in writing, and get HOA sign-off before ordering.
Hinge Replacement
Signs you need it
The gate leans visibly, rubs the ground on one side, or the top hinge pin has worn into an oval.
What it costs in Frisco
Replacing a pair of heavy steel gate hinges in Frisco typically runs $120 to $250 installed.
How we do it
We support the gate, cut or unbolt the failed hinges, weld or bolt new ones in true alignment, and photograph the finished weld.
Gate Rollers
Signs you need it
The gate scrapes when it slides, the roller wheel is flat-sided or wobbling, or the track has a wear groove.
What it costs in Frisco
Replacing a set of slide-gate rollers here runs $180 to $450, depending on gate weight and whether the track needs grinding or replacement.
How we do it
We lift the gate off the old rollers, inspect the track for wear, install new sealed-bearing rollers rated for the gate load, and test travel under power.
What Gate Parts & Welding Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Hinge replacement (one pair) | $120-$250 |
| Single gate roller assembly | $80-$160 |
| Custom weld repair (per hour) | $95-$145 |
How long does a gate weld repair last in Frisco?
A proper steel weld with matched primer and powder-coat touch-up should outlast the surrounding metal. In Frisco’s clay soil, the weld holds; the post movement is what needs watching. Call (469) 613-2832 for an inspection.
Can you match my HOA’s exact gate color in Frisco?
Yes. We keep HOA spec sheets on file for major Frisco subdivisions and confirm the powder-coat RAL or finish code before ordering any replacement steel. Call (469) 613-2832 and bring your community name.
Brands We Service in Frisco
We service nine automation brands including Ghost Controls, DoorKing, and Elite, so a new operator is never the default answer to a failed board or limit switch. Common parts for Ghost Controls and Mighty Mule systems are stocked locally, and most board swaps go in the same visit. Details on our brands.
Pricing for Gate Repair in Frisco, TX
| Service | Typical range in Frisco |
|---|---|
| Gate keypad replacement | $180-$340 |
| Gate remote control | $60-$120 |
| Video intercom replacement | $450-$750 |
| Card reader installation | $500-$900 |
| Phone entry system | $600-$1,200 |
| Hinge replacement (pair) | $120-$250 |
| Gate roller assembly | $80-$160 |
| Post replacement (steel) | $300-$750 |
| Custom weld repair (hourly) | $95-$145 |
| Rail repair (per foot) | $40-$75 |
What pushes the price high in Frisco is almost always access: a post that shifted deep in clay, an HOA that requires a specific finish, or wiring that a summer storm cooked. Whatever the number, you’ll see it in writing before any work starts, and that price doesn’t move unless you approve a change.
Neighborhoods We Serve in Frisco
We cover the whole city, including the HOA-heavy master-planned communities and the older pockets around the rail line. Most repair calls get a technician dispatched the same day.
- Phillips Creek Ranch
- Newman Village
- Starwood
- Stonebriar
- The Trails
Service Area - Cities Near Frisco
Besides Frisco, our crews serve the surrounding metro cities. We’re in Prosper, TX, Little Elm, TX, McKinney, TX, and Plano, TX. Dispatch runs from the Dallas-Fort Worth office, with local crews routed to Frisco and these nearby cities.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Frisco
Same-day dispatch is standard for repair calls. Our crews are routed locally from the Dallas-Fort Worth office, and a live person answers the phone at (469) 613-2832 any hour to schedule.
Most repairs, like hinge or roller replacement, don’t need a city permit. HOA approval can apply when visible finishes or profiles change. We confirm the requirement for your community before ordering parts.
Always. Every Frisco job gets a written flat price before any tool touches the gate, under Haven Standard Clause 1. The price you approve is the price you pay unless you approve a change in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Frisco Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.