Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Murphy Homeowners
A new driveway gate in Murphy typically runs between $3,200 and $9,800 installed, depending on the gate material, width, and whether automation is included from day one. Most single swing gates with a basic opener land in the $4,000 to $6,200 range, while double gates, custom steel work, and heavier access-control setups push toward the upper end. Vance Gate Repair has installed and repaired over 22,000 gates since 2014, and every one of them started with a written price before any tool came off the truck.
We install gates the way Adrian Vance learned to document commercial access-control sites: measure twice, write down what you found, and leave behind a record the next technician can actually use. That means you get a written scope, a flat price, and a photo log of the finished work before we pull out of the driveway. No verbal estimate that changes by Friday, no surprise line item at the end. If you’re weighing a new gate in Murphy, call (469) 613-2832 and we’ll walk the site with you this week.
What Our Gate Installation Service Includes
Gate installation in Murphy is not a one-size-fits-all job. A wrought-iron double gate on a sloped driveway in Maxwell Creek needs different hinges, posts, and motor sizing than a flat aluminum pedestrian gate off Murphy Road. We price each job by what’s actually in the ground and what you actually need the gate to do. Below is how we approach each type.
Driveway Gate
A driveway gate is the vehicle-width gate at the property entrance, and in Murphy it’s usually the first thing a visitor sees. We install steel, aluminum, and wrought-iron driveway gates with or without automation, sized to your actual driveway opening rather than a catalog template. Every driveway gate install includes concrete footings poured to the frost line, post depths matched to the gate weight, and a written record of hinge and latch placement.
Pedestrian Gate
A pedestrian gate is the walk-through gate beside the driveway or along a side fence line. These get ignored by a lot of installers, and then six months later the hinges sag and the latch won’t catch. We hang pedestrian gates with adjustable, heavy-rated hinges on steel or aluminum posts, and we set the latch tension so the gate closes without slamming.
Sliding Gate
Sliding gates are common on Murphy properties where the driveway slopes up toward the house or where a swing gate would need to travel over the sidewalk. A slide gate rides on a track or a cantilever rail, and the two things that matter are the track bed and the stop blocks. We pour a level track bed, weld or bolt the stops precisely where the gate should rest, and photograph the clearance at both ends.
Swing Gate
A swing gate is the classic hinged gate that arcs open and closed, and it’s the most common gate type in Murphy’s residential neighborhoods. Swing gates live or die by the post: undersized posts flex, the gate drops, and the opener burns out against the added resistance. We size posts for the gate’s full weight plus wind load, set the hinge height with a level, and document the degree of travel in the job record.
Double Gate
A double gate is two leaves that meet in the middle, usually across a wider driveway. The failure point on a double gate in Murphy isn’t the gate itself; it’s the gap and the alignment of the two leaves over years of Texas clay shifting under the posts. We align both leaves with a matched reveal, install the center drop rod or lock receiver, and set the opener’s open and closed limit separately for each leaf.
Security Gate
A security gate in Murphy is a gate built for controlled access rather than just curb appeal, often with a keypad, intercom, or access-control loop. We run conduit for power and data at the same time we set the gate posts, so there’s no trenching twice through your yard. Security gate installs include a wiring diagram and a photo log of every connection, because that’s the record that keeps a future repair from becoming a guessing game.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and automate gates with motors from Ghost Controls, DoorKing, Elite, and Mighty Mule, and we’ve touched every one of those brands hundreds of times on service calls before we ever mounted one on a new gate. That matters because a motor that works fine on a 14-foot aluminum gate with our Gate Installation in Wylie can struggle on a 16-foot steel gate in Murphy if the opener is sized from a catalog chart instead of the actual gate. We match the opener’s duty cycle to the gate’s measured weight and width, not the other way around.
Ghost Controls single-swing arms are a good fit for lighter residential gates, and we’ve found their limit setup is simple enough that a homeowner can actually understand the record we leave behind. DoorKing operators are heavier-duty and common on Murphy’s wider double gates, where the solid-state controls reward a clean low-voltage wiring job. Mighty Mule and Elite both show up all over this area; we program their remotes, set their auto-close timers, and integrate their safety edges without steering you toward a different brand just because we happened to have one on the truck. Whatever motor you have or choose, we can wire it, set it, and document it.
BeforeAfterSigns You Need Gate Installation Right Now
- The existing gate is rusted through at the bottom rail. Murphy’s clay soil holds moisture against steel longer than people expect, and once the bottom rail rusts through, the gate loses structural stiffness. Patching buys months, not years. If the rust has eaten into the hinge or motor bracket, replacement is usually cheaper than the labor to reuse it.
- The gate post is leaning and the hinges are tearing out. A leaning post means the footing has failed or was never deep enough to begin with. Torquing the post back and adding concrete will not hold in Texas clay that expands and contracts. A new post, correctly poured, is the fix, and that’s most of what a post-matched gate installation already involves.
- The gate no longer matches the security need. Murphy homeowners who added a pool, a home office, or a side entrance since the original gate was installed often find the walk-through gap and latch are no longer enough. A new security gate with a keypad or intercom puts controlled access at the exact point of entry instead of at the front door.
- The opener is dead, and the gate is too heavy for a simple motor swap. We sometimes see a homeowner sink $900 into a new motor for a gate that was never balanced or sized right, only to burn out the new opener the same season. If the gate is heavy, misaligned, or wider than the old opener’s rating, installing a correctly matched gate and operator together often costs less by the second year.
- You bought the house with a gate you don’t really use. A gate that doesn’t fit how you actually move in and out of the property is a daily annoyance dressed up as an asset. If you’re backing out around it, leaving it open, or wrestling a key every time, that’s a functional failure. We’ll build the gate to the way you actually use the driveway, and document the settings so you’re never locked out of your own approach.
Our Gate Installation Process - Step by Step
- 1
Site visit and written scope. We walk the driveway with you, measure the opening, check the ground for grade and drainage, and note where power will need to come from if you’re adding automation. You get a written scope that names the gate type, post plan, motor if applicable, and the flat price. This is Haven Standard Clause 1: have it in writing, before anything else happens.
- 2
Post and footing work. We mark the exact post locations, dig to depth matched to the gate’s weight and the soil conditions on your street, and pour concrete with the posts set level and square. The concrete cures before the gate goes on. Skipping this wait is how gates end up sagging after the first storm season, so we don’t skip it.
- 3
Gate fabrication or assembly. Custom steel gates are welded and ground smooth, then primed and finished before they leave the shop. Aluminum and fabricated gates are assembled with the hinge and latch hardware we specified in the written scope, not whatever was on the shelf that morning. If you already have a gate, this is when we reinforce or reuse what’s worth keeping.
- 4
Hanging, alignment, and automation. The gate goes on only after the concrete has cured, so the hinges seat into posts that won’t shift. We set the reveal, the latch tension, and the travel limits. If there’s an opener, we run the low-voltage wiring through conduit, set the force limits and safety edges, and program remotes and keypads in front of you so you can test everything before we leave.
- 5
Documentation and walkthrough. Before we pull out of the driveway, you get a photo log of what was installed, a written record of the part numbers and settings, and a walkthrough of the gate’s operation. That record is the whole reason a future technician won’t have to re-diagnose what we already found. Under Clause 4 of the Haven Standard, this documentation is included on every visit, no charge.
How Much Does Gate Installation Cost in Murphy?
A single swing driveway gate in Murphy, welded steel or aluminum, runs roughly $3,200 to $6,200 installed with basic hardware and no automation. Add a matched opener and you’re looking at $4,500 to $8,000 depending on brand and gate weight. A double gate across a wide driveway typically lands between $6,000 and $9,800 with automation, and custom steel with a pedestrian gate or access-control keypad can exceed $10,000. Pedestrian gates alone, set on new posts with good hardware, usually fall between $900 and $2,400.
What moves the price in Murphy: gate width and weight, post depth requirements, whether the ground slopes, how far the conduit run is for power, and whether the existing driveway approach needs concrete work to receive the track or hinges. You avoid overpaying by getting the scope in writing before the job starts, so the price you see is the price you pay, not an opening bid. Our estimates are free and include the written scope, so call (469) 613-2832 and we’ll name the number for your specific gate instead of quoting a range from the internet.
Gate Installation Near Murphy - Our Service Area
Vance Gate Repair installs gates throughout Murphy and the surrounding cities: Wylie, Lucas, Richardson, Allen, Garland, Rowlett, Plano, Fairview, Rockwall, McKinney, and Frisco. Most Murphy installations are scheduled within a week of the written estimate, with emergency gate work available the same day for a gate that will not close or secure the property. We also maintain dedicated service pages for our neighboring communities, including Gate Installation in Wylie and Gate Installation in Lucas, so you can see how we cover each city’s specific sites.
Serving Murphy, TX - Our Local Coverage Area
We’re based in the Murphy area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Murphy
Gate installation is the complete job of setting new gate posts, hanging a new driveway or pedestrian gate, and optionally wiring and programming an automated opener. In Murphy, we treat it as a structural project first and a motor project second, because the best opener can’t fix a gate that was hung on undersized posts. The service includes footings, concrete, hardware, gate, automation if you want it, and a written record of everything we did.
A standard single swing gate with automation in Murphy takes two to three days from first dig to final walkthrough, mostly because the concrete post footings need a full day to cure before we hang the gate. Double gates and custom steel work can run four to five days. We’ll give you the schedule in the written scope, and the date we say is the date we show up.
Most Murphy gate installations cost between $3,200 and $9,800, with single swing gates on the lower end and double gates with automation and custom steel on the upper end. The only way to get an exact number is to measure the opening, check the soil and grade, and decide on automation, which we do at no charge. Call (469) 613-2832 and we’ll write down the price for your gate before you commit to anything.
Yes, we install and automate gates with Ghost Controls, DoorKing, Elite, and Mighty Mule systems routinely across Murphy and the surrounding cities. If you already own one of those openers and want it mounted on a new gate, we’ll integrate it rather than pushing a replacement you don’t need. If you’re buying new, we’ll match the opener to the gate’s actual weight and duty cycle.
Emergency gate installation, where a gate is down and the property can’t be secured, is available same day in Murphy for existing clients and urgent situations. Standard installations are scheduled after a site visit and written estimate, usually within the week. A live person answers (469) 613-2832 at any hour, so if your gate is down tonight, you’ll talk to someone who can actually dispatch a technician, not a voicemail box.
Every gate installation we complete is covered by our 365-Day Done Right Promise: if the installation is not right within a full year, we make it right at no additional charge. That includes sagging, hinge issues, opener settings, and alignment problems that trace back to our workmanship. We also document the installation with photos and a written record, which makes any warranty follow-up fast and factual instead of argumentative.
Clear the driveway approach so we can measure and move material, flag any sprinkler lines or invisible pet fencing you know about, and tell us where you actually want the gate to sit when it’s open. If you have an HOA in Murphy, check whether gate height, color, or style requires approval before we start, since HOA correction notices are faster than concrete cure times. We’ll handle the technical prep; that’s the part you hired us for.
Schedule Your Gate Installation Service in Murphy Today
If you need a new gate in Murphy, get the price in writing before you commit to anything. Call (469) 613-2832 for a free, no-obligation estimate, and we’ll walk the site, write the scope, and hand you a flat price for the gate, the hardware, and the automation if you want it. A live person answers at any hour, and your written estimate is the only number you’ll ever be asked to pay.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Murphy since 2014.