Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in McKinney, TX
Gate access control problems in McKinney usually trace back to one of two things: a keypad or card reader that stopped talking to the opener after a power surge, or a gate that no longer closes because the post shifted on Blackland Prairie clay and the lock no longer lines up. Most jobs we see in Stonebridge Ranch, Craig Ranch, and Trinity Falls involve gates installed between 2005 and 2015 that are now failing on schedule. Call (469) 613-2832 and a live person answers, any hour.
Why McKinney Homes Are Different
McKinney’s master-planned buildout of the 2000s and 2010s concentrated thousands of HOA-governed ornamental iron gates into a tight window. Stonebridge Ranch alone put up enough automated driveway and community-entrance gates to keep a repair company busy year-round, and those gates are now hitting the 15-to-20-year failure point all at once. The Blackland Prairie soil underneath makes it worse: black clay swells in wet seasons and shrinks in drought, heaving posts out of plumb until the gate leaf binds, the opener burns out, or the latch stops aligning. Summers over 100°F cook neoprene seals and circuit boards. The February 2021 freeze seized hydraulic operators and cracked bracket hardware across entire subdivisions in a single week. In Stonebridge Ranch specifically, we routinely find custom iron gates mounted in brick or stone pilasters poured directly over clay without deep footings. The pilaster leans, the gate drags, and the motor dies long before the hinge wears out. Fixing the post is the prerequisite repair, and it is the step most out-of-area companies skip.
Our Main McKinney Services
Here are the three McKinney pages homeowners use most, each covering a different part of the job.
Gate Repair in McKinney
Gate repair in McKinney usually means fixing what the clay soil broke: realigning a dragging leaf, replacing bent hinges, or repairing a weld that cracked when the post shifted. We document the misalignment in photos before we correct it, so you can see exactly what moved. Written price before work starts, every time. See Gate Repair in McKinney for full pricing and detail.
Gate Installation in McKinney
A new gate in McKinney has to be built for Blackland Prairie ground, not just bolted to whatever is there. We set posts below the clay’s active zone and brace for wind load on wider driveway spans. HOA specs matter, and we work from your community’s written requirements. See Gate Installation in McKinney for the process and price ranges.
Gate Motor & Opener in McKinney
McKinney’s heat and freeze cycles are hard on opener electronics. We service LiftMaster, DoorKing, Elite, and Mighty Mule motors already mounted on the property, and we repair rather than replace whenever the board and gearbox are sound. See Gate Motor & Opener in McKinney for motor-specific diagnostics and costs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in McKinney
Gate access control in McKinney is the part of the gate that decides who gets in: keypads, card readers, phone entry, and video intercoms. In Stonebridge Ranch and Craig Ranch, we see a lot of systems installed in the 2010s whose circuit boards are now degrading from summer heat, and whose wiring has worked loose as posts shifted on the clay. This page covers the sub-jobs that make up Gate Access Control, with McKinney pricing in writing before we start.
Keypad Entry
Signs you need it
Codes stop working, the keypad backlight stays off, or one button sticks and locks out the whole panel.
What it costs in McKinney
A keypad replacement or rewire in McKinney runs $180 to $430, depending on whether we are replacing the unit, the cable, or both.
How we do it
We open the housing, test for voltage drop across the wire run, replace only what failed, and photograph the new keypad and the wiring terminations before we leave.
Phone Entry
Signs you need it
Calls ring but the gate won’t open, or the dialer stops calling your cell entirely.
What it costs in McKinney
Phone entry repair in McKinney runs $220 to $520, depending on whether we are replacing the GSM module or upgrading to a cellular dialer.
How we do it
We check the phone line or cellular signal first, then test relay output, and replace the module or reprogram the forwarding number as needed.
Card Reader
Signs you need it
Cards that worked last week now read as invalid, or the reader beeps but the gate never moves.
What it costs in McKinney
Card reader replacement or re-termination in McKinney runs $200 to $480, depending on reader type and whether the controller needs reprogramming.
How we do it
We test the reader at the unit, then at the controller, isolate the failing component, and leave you a written record of every card credential we verified.
Video Intercom
Signs you need it
The screen stays black, audio cuts in and out, or the outdoor unit fogs up and stops sending a clear image.
What it costs in McKinney
Video intercom repair in McKinney runs $280 to $600, depending on whether we replace the monitor, the outdoor camera unit, or the power supply.
How we do it
We test power to both units, check the cable for shorts, replace the failed component, and photograph the camera view after calibration.
What Gate Access Control Costs in McKinney
| Item | Typical range in McKinney |
|---|---|
| Keypad replacement or rewire | $180 - $430 |
| Phone entry repair or module swap | $220 - $520 |
| Card reader replacement | $200 - $480 |
Can you reprogram an existing keypad without replacing it?
Usually yes. If the keypad still powers on and the buttons respond, we can reprogram codes on site. If the circuit board is heat-damaged, replacement is cheaper than repeated callbacks.
Do you handle access control for HOA community gates?
We service both residential driveway access and community-entry systems. HOA board requirements vary, so we review the written spec before quoting. Call (469) 613-2832 for a free estimate.
Gate Parts & Welding in McKinney
Gate parts and welding in McKinney covers the metal and mechanical pieces that fail first: hinges, posts, rails, rollers, and the welds holding them together. On Blackland Prairie clay, posts move, welds crack, and hinges bend over months, not years. This page covers the sub-jobs that make up Gate Parts & Welding, with McKinney-specific pricing in writing before we start.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground, or the hinge pin shows visible wear and ovaling.
What it costs in McKinney
Hinge replacement in McKinney runs $150 to $400 per hinge, depending on gate weight and whether we need to weld or bolt the new hinge in.
How we do it
We support the gate, cut or unbolt the old hinge, set the new one level, and photograph the gate after it swings freely again.
Post Replacement
Signs you need it
The post leans visibly, the gate gap opens or closes by inches, or concrete at the base is cracked.
What it costs in McKinney
Post replacement in McKinney runs $600 to $2,800, depending on whether it is a simple steel post or a stone pilaster that needs rebuilding.
How we do it
We dig below the active clay zone, set the new post in deep concrete, brace it square, and return after the concrete cures to rehang and align the gate.
Custom Welding
Signs you need it
A crack opens in a picket, a bracket snaps, or the frame separates at a corner.
What it costs in McKinney
Custom welding repair in McKinney runs $150 to $600, depending on how much grinding, fitting, and re-welding the joint needs.
How we do it
We clean the joint, grind out the crack, weld it in position, and photograph the repair before and after, leaving you the record.
Gate Rollers
Signs you need it
A slide gate chatters, jumps the track, or the roller wheels show flat spots and seized bearings.
What it costs in McKinney
Gate roller replacement in McKinney runs $140 to $380, depending on wheel diameter and whether the track needs adjustment.
How we do it
We lift the gate enough to swap the rollers, set the wheel pressure against the track, and test the full travel before we photograph the result.
What Gate Parts & Welding Costs in McKinney
| Item | Typical range in McKinney |
|---|---|
| Hinge replacement | $150 - $400 per hinge |
| Post replacement | $600 - $2,800 |
| Custom welding repair | $150 - $600 |
Can you weld a gate while it is still hanging?
Sometimes, if the crack is accessible and the gate can be braced safely. Ground-out and re-welded joints, done in place, save the labor of removal.
How fast can you replace a bent hinge on a sagging gate?
We carry common hinge sizes on the truck, so most hinge replacements happen the same visit. Call (469) 613-2832 to schedule and get a written quote first.
Brands We Service in McKinney
We service LiftMaster, DoorKing, Elite, and Mighty Mule openers, among others, and we stock common control boards, remotes, and safety parts locally so most McKinney repairs do not wait on a shipped part. See our brands for the full list.
Pricing for Gate Repair in McKinney, TX
| Service | Typical range in McKinney |
|---|---|
| Keypad replacement or rewire | $180 - $430 |
| Phone entry repair or module swap | $220 - $520 |
| Card reader replacement | $200 - $480 |
| Video intercom repair | $280 - $600 |
| Hinge replacement | $150 - $400 per hinge |
| Post replacement | $600 - $2,800 |
| Custom welding repair | $150 - $600 |
| Gate roller replacement | $140 - $380 |
The two things that push McKinney pricing up are leaning posts on clay soil and heat-damaged control boards, both of which show up more often here than in neighboring cities with denser soil or cooler summers. Every price above is written down and handed to you before work starts, under our Haven Standard, so there is no surprise at the end.
Neighborhoods We Serve in McKinney
We work throughout McKinney, from the newer subdivisions east of US 75 to the mature streets around Craig Ranch and Stonebridge Ranch. Response time across the area is typically same day for repair calls.
- Stonebridge Ranch
- Craig Ranch
- Trinity Falls
- Adriatica
- Westridge
Service Area - Cities Near McKinney
We also serve the neighboring communities around McKinney, including Allen, TX, Prosper, TX, Plano, TX, and Wylie, TX. If you are outside McKinney proper, call (469) 613-2832 and we will confirm coverage before you book.
Serving McKinney, TX - Our Local Coverage Area
We’re based in the McKinney area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in McKinney
Most repair calls in McKinney are scheduled same day. A live person answers the phone 24/7, so you will get a real conversation, not a voicemail. The written price is prepared before any work starts.
If your home is in a Stonebridge Ranch or Craig Ranch HOA, the community’s design guidelines may require approval for visible changes like a new gate finish or post replacement. We work from your HOA’s written spec and can document the repair for the committee.
Yes, and that is the entire point. We inspect the gate, write down the diagnosis and the price, and hand it to you before any work begins. Call (469) 613-2832 to schedule the visit.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What McKinney Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.