Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Garland
Gate installation in Garland usually means replacing a gate that’s been failing for years, not starting from a blank fence line. Most homes here were built between 1960 and 1985, and the original wood swing gates on those properties are now forty to sixty years old. The clay soil under Garland doesn’t help: Blackland Prairie clay swells with every rain and contracts hard in summer drought, which slowly works gate posts out of plumb.
At Vance Gate Repair Murphy, we plan every installation around that soil movement, not against it. If you’re tired of a gate that drags, sags, or won’t stay latched, call (469) 613-2832. We’ll come out to your Garland property, take measurements, check the posts and footing, and hand you a written price before any work begins.
Why Vance Gate Repair Murphy Is Garland’s Preferred Gate Installation Company
Garland homeowners call us because we show up with a plan and a written number, not a handshake estimate that drifts. Adrian Vance built this company on a commercial access-control habit: document what you find, price it in writing, and leave a record the homeowner keeps. That approach works whether the gate is a 1978 wood swing in an alley off Broadway Blvd or a new ornamental steel driveway gate in a subdivision near the Rowlett border.
Our crews know Garland’s housing stock. We’ve worked in neighborhoods from the established east side near Duck Creek to the newer master-planned pockets close to Sachse and Wylie. The gate you have tells us something about the house: a split-rail mortise and corroded strap hinge means pre-1980 construction. A steel frame with a late-model operator means something newer. That matters when we’re sizing footings, choosing hinges, and deciding whether your existing gate is worth retrofitting.
Every job includes a documented photo record: what we found, what we set, what we installed. And our 365-Day Done Right Promise means if the installation isn’t right within a year, we make it right at no charge. No argument, no fee.
Our Gate Installation Services in Garland
Most of our work in Garland falls into four categories. Each one starts the same way: we come out, look at the gate and the ground it’s sitting on, and write down the price. You can also read more about our full Gate Installation capabilities if you’re still deciding between repair and replacement.
Driveway Gate Installation
Driveway gates in Garland range from simple single-swing wood panels to automated ornamental iron systems. On older ranch-style homes, the driveway gate is usually a wood swing that’s been repaired so many times the hinge post looks like Swiss cheese. We’ll tell you honestly: if the post is solid and the panel is straight, we can hang a new gate for less than a full rebuild. If the post has heaved or the panel is split at the rails, replacement is usually cheaper than another patch job.
Pedestrian Gate Installation
Pedestrian gates, the walk-through gates beside the driveway or between the front and back yard, fail in predictable ways in Garland. The latch plate wobbles, the hinge screws strip out of weathered wood, the bottom rail drags on the sidewalk. We install steel and cedar pedestrian gates sized to your existing opening, with hardware rated for North Texas weather. A typical pedestrian gate installation in Garland runs $450 to $1,200 depending on width, material, and whether we need to replace the posts.
Sliding Gate Installation
Sliding gates are less common on Garland’s older residential lots, but they show up on wider driveways and some of the newer properties near Sachse. Sliding gates need a level track or cantilever setup, and in Garland’s clay soil that track has to be engineered properly or it will shift within two seasons. We install track and cantilever sliding gates, and we always pour footings deep enough to get below the active clay zone.
Swing Gate Installation
Swing gates are the default in Garland, and we install more of them than anything else. The critical variable is the post. A swing gate puts all its weight in rotation against the hinge post, and in expansive clay that post wants to move. We set posts in concrete footings that reach below the frost line and below the seasonal moisture band, with gravel drainage at the base. A new swing gate installation in Garland typically runs $900 to $2,800 for a single gate, depending on size, material, and whether we’re adding automation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Garland
Garland homes have a mix of gate operators, depending on when the house was built and what the previous owner installed. We work on FAAC, BFT, Linear, and Viking operators, among others, so we’re not going to tell you to rip out a perfectly good motor and buy whatever brand we happen to stock. If your existing operator has a dead control board or missing safety sensors, we can often retrofit it to work with a new gate instead of replacing it. Our crews carry common control boards, photo-eyes, and edge sensors on the truck, which means fewer trips back to a supply house and faster completion on your Garland job.
Common Gate Installation Problems We See in Garland Homes
- Posts heaving out of plumb from clay soil movement. Blackland Prairie clay expands and contracts with every rain cycle and every dry spell. Posts set directly in that soil will move, no matter how tight the gate was installed. We fix this by pouring footings below the active clay layer, and we’ve seen firsthand how a gate that’s straight in April can drag by August if the footing is shallow.
- Wood swing gates splitting at the rail mortise. The joint where the horizontal rail enters the vertical stile is the weak point on old wood gates. Once water gets in and ice swells the joint, the mortise splits open and the gate drops. That’s a structural failure, not a hinge adjustment, and it’s the single most common reason Garland homeowners replace rather than repair.
- Alley gates in worse shape than the front gate. In pre-1980 Garland neighborhoods with rear service alleys, the alley gate is almost always worse off. Garbage trucks slam it, nobody lubricates it, and it’s out of sight so the damage accumulates unnoticed. We’ve lost count of the installation calls where the homeowner called about the front gate, and we found the alley gate hanging by one hinge.
- Obsolete operators without modern entrapment protection. Gates installed before UL 325 became standard often have no photo-eye and no reversing edge. If we’re installing a new automatic gate in Garland, current safety standards require an entrapment sensor: a photo-eye, an edge sensor, or both. We won’t automate a gate without them.
Pricing for Gate Installation in Garland, TX
Here’s what Gate Installation in Garland actually costs, in dollars. A basic pedestrian gate replacement runs $450 to $1,200. A single wood or steel swing gate installation runs $900 to $2,800. A double driveway gate, which is two panels meeting in the middle, runs $2,400 to $6,500 depending on material and automation. An automated sliding gate on a track or cantilever system starts around $3,500 and can reach $9,000 for wide ornamental steel.
What moves the price? Material (cedar vs. ornamental steel), gate width and weight, whether we’re replacing posts or just the gate panel, and whether automation is included. We’ll write the number down before we start, under Haven Standard Clause 1, and that’s the price you pay. No surprise invoice at the end. Call (469) 613-2832 for a free on-site estimate.
We Also Serve Cities Near Garland
Our crews serve Garland and the surrounding cities across northeast Dallas County and Collin County. If you’re in Rowlett, Wylie, Richardson, or Plano, we can usually schedule within the same week. We coordinate dispatch from our Dallas-Fort Worth office, and the crew that shows up is the crew that does the work. Read more about our service area on the Gate Installation in Garland page.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Garland
Garland sits on Blackland Prairie clay, a soil that expands dramatically when wet and contracts when dry. If a post is set in a shallow concrete footer that doesn’t extend below the active clay zone, the soil movement will work the post out of plumb within a few seasons. The fix is a deeper footing with proper drainage, and that’s standard practice on our Garland installations. A post that’s already heaved can’t be straightened; it has to be pulled and re-set.
Yes, you can often retrofit a modern operator onto an existing swing gate, provided the gate itself is structurally sound and the hinges and posts are solid. The operator mounts to the gate and the post, so both have to be able to handle the load. If the gate is split at the rails or the post has heaved out of plumb, we’ll tell you plainly: retrofitting the operator won’t solve the underlying problem, and you’ll be back in the same spot next year. Call (469) 613-2832 and we’ll assess it for free.
If the gate frame is rusted through at the hinge mount points, new hinges won’t save it; the metal is gone and welding on top of rust is a temporary fix. But if the frame is solid and only the hinges are worn, we can replace the hinges and often add a few more seasons to the gate. We see alley gates in Garland’s older east-side neighborhoods where the hinge leaf has rusted away while the gate frame is still serviceable. We’ll show you photos either way before you commit.
Yes. Automatic gate operators installed after the UL 325 standard took effect must include entrapment protection: a photo-eye, a reversing edge sensor, or both, depending on the installation. Older Garland gates may not have these, but if we’re touching the operator or installing a new one, we’re required to bring it up to code. We won’t automate a gate without proper safety sensors, no exceptions.
That’s your Blackland Prairie clay soil doing exactly what it always does. Spring rains swell the clay and shift the post slightly. Summer drought contracts the soil and the post settles, usually not back where it started. Over a few seasons, that cycle adds up to a gate that drags on the latch side or gaps at the top. We saw this on a ranch near Broadway Blvd, where a 1978 swing gate’s hinge post had heaved so far out of plumb we had to pour a new footing and reset the post before hanging a new steel gate. The old operator was a LiftMaster with a burned control board, but replacing the motor alone wouldn’t have fixed the dragging. Call (469) 613-2832 for a free estimate on getting your gate straight again.
Call Vance Gate Repair Murphy for Gate Installation in Garland
If your Garland gate is dragging, sagging, or rusted through, we’ll come out, look at it, and hand you a written quote before any work starts. That’s the whole point of our business. A live person answers the phone at (469) 613-2832, 24 hours a day, every day of the year. No voicemail loop, no callback queue. Tell us what’s going on with your gate, and we’ll schedule a time to see it in person.
Written by Adrian Vance, Owner at Vance Gate Repair Murphy, serving Garland and the surrounding DFW metro since 2014.
Gate Installation in Nearby Areas
