Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Richardson, TX
Gate access control is the service we get called for most in Richardson, and the reason is written into the city’s layout. The Telecom Corridor along US-75 is dense with office parks and tech campuses running automated gates and card readers, while the older neighborhoods south of Belt Line are full of 1950s-to-1970s ranch homes with original iron driveway gates now 40 to 50 years old. Those two worlds create a specific mix of work: commercial access systems during the week, sagging residential gates on weekends. Call (469) 613-2832 and a live person answers, any hour.
Why Richardson Homes Are Different
Richardson sits on North Texas black clay, and that soil is the single biggest factor in every gate repair we do here. The clay swells after spring rains and contracts hard during summer droughts, which slowly pushes gate posts out of plumb and racks frames out of square. In the older south-side neighborhoods, posts set in the 1970s often sit in shallow concrete entirely within the active clay zone, so a hinge fix will not hold six months if the post is still moving seasonally. The real repair is usually digging down 36 to 42 inches and repacking with concrete to get below the shrink-swell layer.
Housing stock matters too. Central and south Richardson are dominated by brick ranch homes with wrought-iron gates showing hinge sag, latch failure, and rust from decades of wet-dry cycles. North Richardson’s newer HOA communities, built mostly in the 1990s and 2000s, specify ornamental iron or aluminum gates with height and style standards that must be matched exactly or the homeowner gets a violation notice. Summer heat above 100°F also accelerates paint failure and oxidation on south- and west-facing iron, so rust-through on the lower rail is a common find.
Our Main Richardson Services
Most Richardson calls fall into three categories: a gate that will not open or close properly, a gate that needs to be replaced entirely, or a motor that has stopped responding. Each has its own dedicated page with pricing and details.
Gate Repair in Richardson
When a Richardson gate is sagging, dragging, or latched but not latching, the cause is almost always either a failing hinge, a bent rail, or a post that has shifted in the expansive clay. We diagnose the full picture, not just the symptom, and the written quote covers what will actually keep the gate working. Full details are on the Gate Repair in Richardson page.
Gate Installation in Richardson
New gate installs in Richardson mean matching HOA standards in the north or respecting the scale of a 1960s ranch in the south. We measure, order, pour posts deep enough to survive the clay, and hang the gate with a written price before any work starts. See the Gate Installation in Richardson page for what a full install includes.
Gate Motor & Opener in Richardson
When a swing or slide gate motor fails in Richardson, the control board, limit switches, or a burned capacitor are the usual suspects, and we service nine automation brands rather than pushing a replacement. The Gate Motor & Opener in Richardson page lists common failures and repair ranges by brand.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Richardson
Gate access control in Richardson means keypads, card readers, phone entry, and video intercoms on both commercial properties along the Telecom Corridor and residential gates in neighborhoods like Canyon Creek and Reservation. The commercial systems here are often the same hardware we have serviced since Adrian Vance started doing access-control work in 2014, while residential keypads fail more often from sun exposure and moisture in the clay-rich ground. Gate Access Control work is where written documentation matters most, because a misconfigured relay or a corroded wire splice can frustrate a whole office park or a single driveway for weeks if nobody photographed the original wiring.
Keypad Entry
Signs you need it
The keypad accepts some codes but not others, or the buttons need multiple hard presses before they register.
What it costs in Richardson
Replacing a wired residential keypad in Richardson typically runs $180 to $340, depending on whether the old wiring is reusable.
How we do it
We test voltage at the keypad, trace the wiring back to the operator board, replace the unit, and photograph the new splices before sealing the housing.
Remote Control
Signs you need it
The gate opens only when the remote is within a few feet, or a remote that worked last week now does nothing.
What it costs in Richardson
A replacement remote programmed on-site in Richardson runs $60 to $150, including pairing and testing.
How we do it
We identify the receiver frequency and protocol, match a compatible remote from the brands we stock, program it, and leave a written record of the codes added.
What Gate Access Control Costs in Richardson
| Item | Typical range in Richardson |
|---|---|
| Keypad replacement (wired residential) | $180-$340 |
| Remote control programmed | $60-$150 |
| Access control system diagnosis | $95-$185 |
Can you service the access system on our Richardson office park gate?
Yes. We handle card readers, phone entry, and video intercom on commercial gates across Richardson, including the Telecom Corridor office campuses. Most repairs are diagnosed and quoted within one visit. Call (469) 613-2832.
Will a new keypad work with our existing operator?
Most Richardson gates use LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule operators, and we match the keypad to the board’s input type before ordering anything. We verify compatibility during diagnosis. Call (469) 613-2832 for a written quote.
Gate Parts & Welding in Richardson
Gate parts and welding in Richardson are usually about one of two things: a 1970s wrought-iron gate with rusted hinges and a broken picket, or a post that has leaned so far the gate will not close. The black clay soil pushes posts out of alignment every wet-dry season, and welding a cracked rail back together is pointless if the post under it is still moving. Gate Parts & Welding calls in Richardson often end with a reset post, a new hinge, and touched-up paint rather than a full gate replacement.
Hinge Replacement
Signs you need it
The gate drags on the latch side, or you can see the hinge pin has worn an oval into the barrel.
What it costs in Richardson
Replacing a pair of hinges on a Richardson iron gate typically runs $150 to $400, depending on gate weight and whether welding is required.
How we do it
We support the gate, cut or unbolt the old hinges, weld or bolt replacements, and photograph the final alignment before testing the swing.
Post Replacement
Signs you need it
The gate post leans visibly, the gate self-swings open or closed, or the latch no longer lines up with the receiver.
What it costs in Richardson
Digging out and resetting a gate post in Richardson’s clay soil typically runs $300 to $800, including concrete and haul-away.
How we do it
We excavate the old footing, set the new post 36 to 42 inches deep below the active clay zone, pour concrete, and brace it until cured.
What Gate Parts & Welding Costs in Richardson
| Item | Typical range in Richardson |
|---|---|
| Hinge replacement (pair) | $150-$400 |
| Post replacement with concrete | $300-$800 |
| Custom welding repair | $120-$450 |
Can you weld a broken picket on our 1960s iron gate?
Yes. We match the picket profile, weld it in place, grind the joint smooth, and repaint to blend with the existing finish. The repair is photographed and included in your job record. Call (469) 613-2832.
Does the post really need to be dug out, or can you just shim it?
In Richardson’s expansive clay, shimming is usually temporary. If the post is moving seasonally, the footing is too shallow and the repair will not hold. We verify footing depth before recommending resetting.
Brands We Service in Richardson
We service gate motors and access systems from FAAC, BFT, Linear, and Viking, plus five other major automation brands, and we stock common remotes, keypads, and photo-eyes in the metro for same-day turnaround on many Richardson jobs. Our brands page lists everything we work on.
Pricing for Gate Repair in Richardson, TX
| Service | Typical range in Richardson |
|---|---|
| Gate repair diagnosis and minor adjustment | $95-$250 |
| Hinge replacement (pair) | $150-$400 |
| Post replacement with concrete | $300-$800 |
| Keypad replacement (wired residential) | $180-$340 |
| Remote control programmed | $60-$150 |
| Custom welding repair | $120-$450 |
| Gate motor capacitor replacement | $145-$285 |
| Access control system diagnosis | $95-$185 |
What pushes a Richardson gate repair higher is usually soil movement: a post that must be excavated and reset below the active clay layer costs more than a simple hinge swap, but it is the only fix that lasts. Every job gets a written price before work begins, and that price does not change unless you approve a change in scope in writing first.
Neighborhoods We Serve in Richardson
We work across all of Richardson, from the older ranch-home streets south of Belt Line to the HOA communities north of Campbell Road and the commercial gates along US-75. Most Richardson calls get a same-day or next-day visit.
- Canyon Creek
- Reservation
- Heights Park
- Cottonwood Heights
- University Estates
Service Area - Cities Near Richardson
Beyond Richardson, our crews cover the surrounding Dallas-Fort Worth metro with the same written-price standard. We regularly handle gate repair in Plano, TX, Garland, TX, Carrollton, TX, and Allen, TX, with the same documented photo record on every visit.
Serving Richardson, TX - Our Local Coverage Area
We’re based in the Richardson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Richardson
Most Richardson calls get a same-day or next-day visit. A live person answers the phone 24 hours a day at (469) 613-2832, and we schedule directly rather than through a callback queue or voicemail.
If your home is in a north Richardson HOA community, the HOA likely has written standards for gate height, style, and color. We match those specifications exactly when replacing a gate or welding new parts, and we can provide a written description of the work for your HOA application.
Bring the other company’s written estimate to us and we will review it at no cost as a free second opinion. The comparison only works if both quotes specify the same scope in writing, and ours always does before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Richardson Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.